Joined in 2023 
82 
63 About this deal
The 3611 Serial to Ethernet Serial Port adapter supports multiple network protocols, such as TCP, UDP, ARP, ICMP, HTTP, DNS and DHCP. It also allows remote management including access control and rapid configuration. When it comes to choosing the right RS232 cable, there are a few key considerations that you should keep in mind to ensure that you get the right cable for your needs. Here are some of the top considerations to keep in mind: The standard does not define a maximum cable length, but instead defines the maximum capacitance that a compliant drive circuit must tolerate. A widely used rule of thumb indicates that cables more than 15m (50ft) long will have too much capacitance, unless special cables are used. By using low-capacitance cables, communication can be maintained over larger distances up to about 300m (1,000ft). [13] For longer distances, other signal standards, such as RS-422, are better suited for higher speeds. Universal Compatibility: Additionally, RS232 is a well-established standard, which means that there are many different devices and cables available that support the protocol.
To transmit data effectively, RS232 utilizes a method called data encoding. It converts the binary data into a format suitable for transmission over the serial connection. Commonly used encoding schemes include ASCII (American Standard Code for Information Interchange) and Unicode. Start and Stop Bits
Serial to Ethernet Converter software
Null-modem cables are used to connect two DTE devices together, while crossover cables are used to connect two DCE devices together. Data and control signals [ edit ] Male pinout of a 9-pin (D-subminiature, DE-9) serial port commonly found on 1990's computers Male pinout of a 25-pin serial port (D-subminiature, DB-25) commonly found on 1980's computers Limited Range: One of the main disadvantages of RS232 is its limited range. RS232 is designed for short-distance communication, typically no more than 50 feet.
Slow Transmission Speed: RS232 is a relatively slow communication protocol compared to more modern alternatives.
Cable Length: One of the most important considerations when choosing an RS232 cable is the length of the cable. RS232 signals can only travel so far, and the longer the cable, the more likely you are to experience signal degradation or loss. So, it’s important to choose a cable that is the right length for your needs. Connect RS232 to Ethernet converter to your computer using either a standard Ethernet cable or crossover or straight-through cable. Connect it to the power supply.
Isolated RS232 + Isolated RS485 (the 2 channels can receive and transmit independently at the same time) A minimal "3-wire" RS-232 connection consisting only of transmit data, receive data, and ground, is commonly used when the full facilities of RS-232 are not required. Even a two-wire connection (data and ground) can be used if the data flow is one way (for example, a digital postal scale that periodically sends a weight reading, or a GPS receiver that periodically sends position, if no configuration via RS-232 is necessary). When only hardware flow control is required in addition to two-way data, the RTS and CTS lines are added in a 5-wire version. For access to remote console ports on routers, switches,etc, Perle IOLAN’s enable administrators secure access to these RS232 ports via inband Reverse Telnet / SSH or out of band with dial-up modems. Perle IOLAN models with integrated modems are available. In fields such as laboratory automation or surveying, RS-232 devices continue to be used. Some types of programmable logic controllers, variable-frequency drives, servo drives, and computerized numerical control equipment are programmable via RS-232. Computer manufacturers have responded to this demand by re-introducing the DE-9M connector on their computers or by making adapters available.Compared with later interfaces such as RS-422, RS-485 and Ethernet, RS-232 has lower transmission speed, shorter maximum cable length, larger voltage swing, larger standard connectors, no multipoint capability and limited multidrop capability. In modern personal computers, USB has displaced RS-232 from most of its peripheral interface roles. Thanks to their simplicity and past ubiquity, however, RS-232 interfaces are still used—particularly in industrial CNC machines, networking equipment and scientific instruments where a short-range, point-to-point, low-speed wired data connection is fully adequate. [3] Scope of the standard [ edit ]
Since the standard definitions are not always correctly applied, it is often necessary to consult documentation, test connections with a breakout box, or use trial and error to find a cable that works when interconnecting two devices. Connecting a fully standard-compliant DCE device and DTE device would use a cable that connects identical pin numbers in each connector (a so-called "straight cable"). " Gender changers" are available to solve gender mismatches between cables and connectors. Connecting devices with different types of connectors requires a cable that connects the corresponding pins according to the table below. Cables with 9 pins on one end and 25 on the other are common. Manufacturers of equipment with 8P8C connectors usually provide a cable with either a DB-25 or DE-9 connector (or sometimes interchangeable connectors so they can work with multiple devices). Poor-quality cables can cause false signals by crosstalk between data and control lines (such as Ring Indicator). In this scheme, commonly called "RTS/CTS flow control" or "RTS/CTS handshaking" (though the technically correct name would be "RTR/CTS"), the DTE asserts RTS whenever it is ready to receive data from the DCE, and the DCE asserts CTS whenever it is ready to receive data from the DTE. Unlike the original use of RTS and CTS with half-duplex modems, these two signals operate independently from one another. This is an example of hardware flow control. However, "hardware flow control" in the description of the options available on an RS-232-equipped device does not always mean RTS/CTS handshaking. Dynamic DNS – Easy console management access from anywhere on the Internet 4, 8, 16 or 24 serial RS232 on RJ45 PortsModern communications environments use full-duplex (both directions simultaneously) modems. In that environment, DTEs have no reason to deassert RTS. However, due to the possibility of changing line quality, delays in processing of data, etc., there is a need for symmetric, bidirectional flow control. To conveniently work with such equipment we need to access remote devices, and the easiest way to do it would be to convert a serial port to Ethernet. Isolated RS232/485/422 (choose one, only one interface can be used for communication at the same time) Keeping in mind that not all device manufacturers maintain the standard all the way through, it’s a good practice to study up on the documentation and to use a breakout box to test every new connection. In some cases, only the trial and error method can help to find the right cable to connect each pair of devices. The device can in fact be called a serial to Ethernet converter, adapter, console, or device server and come in various models, depending on the number of fitted serial ports. Here are some examples of serial to Ethernet hardware:
Great Deal 
New Comment